Multi-Story Facade Wrap

Multi-Story Facade Wrap — made to your size in a choice of 2 fabrics, from 120gsm to 480gsm.

Building wraps are the largest format we produce and the least forgiving. They are installed at height, they stay up for months or years, and getting one down to fix a problem is expensive — so the specification has to be right before anything is printed.

This product is offered across more than one fabric because the right answer depends on where the panel is going and how long it needs to last. The table below sets every option side by side on the specifications that actually decide the choice — weight, opacity, finish and weather behaviour — so you can compare them directly rather than opening a page for each one.

About this format

A multi-storey wrap is supplied as panels. Panelling is how large wraps are meant to be done: individual panels are straightforward to handle at height, they tension evenly, and any single panel can be swapped on its own.

Best for

• Full and partial facade wraps
• Multi-storey building graphics
• Retail storefront wraps
• Development and hoarding facade panels
• Feature-wall and architectural graphics

Fabric options compared

Which fabric should you choose?

• 600D Tarpaulin (480gsm) — The heaviest cloth we print — specified when a graphic has to stay up for years, not months.
• 120gsm Mesh — A perforated cloth that lets wind pass straight through — the honest answer to an exposed site.

Key advantages

• One product, 2 fabric specifications — compare and choose without leaving the page
• Longest outdoor service life in the range by a clear margin
• Thick coated construction shrugs off abrasion, grit and repeated tensioning
• Fully opaque, so artwork stays dense and readable in direct sun
• Takes welded hems and heavy-duty eyelets for secure structural fixing

Choosing the right specification

Specify for the wind, then specify for the years. Mesh for anything large and exposed; a coated tarpaulin where the wrap is sheltered and needs to last. Panel large facades rather than attempting a single piece — seamed panels are easier to handle at height, easier to tension evenly, and far easier to replace individually if one is damaged.

How ordering works

• Send your artwork — Upload print-ready artwork at any stage — we check scale, resolution and bleed before anything goes to press and come back to you if something needs adjusting.
• Made to your size — Every panel is cut and finished to your dimensions. Tell us the finished size you need and how it is being fixed, and we will allow for hems and fixings correctly.
• Printed by dye-sublimation — Colour is transferred into the polyester fibre under heat, so the image becomes part of the cloth rather than a layer sitting on top of it.
• Finished and shipped — Hems, eyelets, pole pockets, silicone edge and other finishing are applied before your order is folded, boxed and dispatched worldwide.

Related specifications

Closely related products in this range include Feature Wall Wrap, Retail Storefront Wrap, Small Building Facade Wrap. They share this fabric and finish, so the choice comes down to format and size.

Technical detail

Why a heavier coating lasts longer outdoors. Coating mass is what stands between the yarn and ultraviolet light, and UV combined with heat cycling is what ends the life of an outdoor graphic, not water. A tarpaulin-grade coating carries far more mass per square metre than a standard PU finish, which is the reason this construction is specified for installations measured in years rather than months.

What to expect from service life. Indoors and out of direct sun, printed polyester holds its appearance for five years or more. Outdoors, published ranges for dye-sublimated polyester run from roughly six to twenty-four months depending on how exposed the position is, with the shorter end applying in high-ultraviolet regions such as the Southwest, Florida and the Gulf Coast, and in coastal or high-wind locations. Sheltered and north-facing installations reach the longer end. Coated and tarpaulin-grade constructions extend beyond that band because the coating carries the UV load.

Best suited to

Multi-year outdoor installations where the cost of taking a graphic down outweighs the cost of buying a heavier one — building wraps, long-term hoarding and site enclosures.

Also in this range

For portable and hand-carried work, our lighter Oxford and PU ranges are easier to handle; for very exposed spans, our vented mesh reduces wind load.

Not sure which fabric is right? Order a free swatch pack and see the weight, texture and finish in your own hands before you commit to a full run.