Hi-Vis Orange Fence Banner (300D Fluor)
Proof before print: every order gets a digital proof for approval. Turnaround: printed in 24–48 h, delivered worldwide in 7–10 days. Trade accounts: volume pricing from 50 sq ft.
Hi-Vis Orange Fence Banner (300D Fluor) — Oxford durability on a fluorescent ground — built for sites where being seen is the job, specified for fence banners.
This pairs the dense Oxford construction used across our outdoor range with a fluorescent base colour. You get the handling tolerance and tension behaviour of a woven banner cloth, plus a ground that stays conspicuous in poor light. It is the combination most often specified for construction hoarding, site marshalling and event perimeter work.
A banner on a fence line is a structural decision as much as a graphic one. Wind loads on a large solid panel are substantial, and they transfer straight into the fence, the posts and whatever is holding those posts in the ground.
Fluorescent orange
Fluorescent orange is the higher-contrast of the two safety colours against green, grey and blue backgrounds — vegetation, tarmac, concrete and sky. It is the usual choice for construction, highway and outdoor-site work, where the panel is seen against the landscape rather than against a building.
Best for
- Chain-link and mesh fence banners
- Sports-field perimeter banners
- Construction-site fence graphics
- Event perimeter and crowd-line banners
- Temporary boundary and marshalling banners
Key advantages
- Fluorescent ground stays readable at distance and in the flat light of early morning and dusk
- Dense woven body tolerates cable ties, tension straps and repeated re-fixing
- Opaque, so artwork reads cleanly with no ghost image showing through
- Holds shape across long spans without stretching at the fixing points
- Practical for both temporary site work and season-long installations
Specifications
| Material & construction | High-density Oxford weave on a fluorescent dyed base |
|---|---|
| Yarn denier | 300D |
| Fabric weight | 190 gsm |
| Print method | Dye-sublimation (colour transferred into the fibre) |
| Print sides | Double |
| Opacity | Opaque |
| Finish & feel | Firm woven surface, high-chroma fluorescent ground |
| Wind & breathability | Holds form under load; we vent or mesh-panel large spans for exposed positions |
| Water resistance | Sheds light rain; hems and eyelets are stitched, so we specify this as water-resistant |
| Indicative service life | Outdoor 1-2 yrs (shorter in high-UV regions) |
| Recommended finishing | Welded or sewn hems, reinforced corners, brass eyelets, tension straps |
| Care | Sponge clean with mild detergent and cool water; air dry fully before folding |
| Material & recycling | 100% polyester, mono-material and recyclable through polyester streams |
| Typical weight for this denier | 130-250 g/m² across the industry (base 130-180, rising to about 250 with coating and higher thread density) |
Choosing the right specification
On any exposed run longer than a few metres, use a vented mesh rather than a solid cloth. Mesh lets the wind through instead of catching it, which is the difference between a banner that survives a storm and a fence panel that ends up flat on the ground. Fix at grommets spaced about 24 inches around the full perimeter, adding extra ties at the top, bottom and centre on large or exposed panels, and let the reinforced eyelets carry the load rather than the fabric.
How ordering works
- Send your artwork — Upload print-ready artwork at any stage — we check scale, resolution and bleed before anything goes to press and come back to you if something needs adjusting.
- Made to your size — Every panel is cut and finished to your dimensions. Tell us the finished size you need and how it is being fixed, and we will allow for hems and fixings correctly.
- Printed by dye-sublimation — Colour is transferred into the polyester fibre under heat, so the image becomes part of the cloth rather than a layer sitting on top of it.
- Finished and shipped — Hems, eyelets, pole pockets, silicone edge and other finishing are applied before your order is folded, boxed and dispatched worldwide.
Related specifications
This is the 300D version. Other sizes and weights in the same fabric are made to order — tell us the finished dimensions you need and we will quote them.
Technical detail
What to expect from service life. Indoors and out of direct sun, printed polyester holds its appearance for five years or more. Outdoors, published ranges for dye-sublimated polyester run from roughly six to twenty-four months depending on how exposed the position is, with the shorter end applying in high-ultraviolet regions such as the Southwest, Florida and the Gulf Coast, and in coastal or high-wind locations. Sheltered and north-facing installations reach the longer end. Coated and tarpaulin-grade constructions extend beyond that band because the coating carries the UV load.
Best suited to
Site and safety work that has to stay conspicuous through a full season outdoors — construction hoarding, highway signage and event marshalling.
Also in this range
For multi-year installations, our coated PU and tarpaulin ranges extend service life; for very exposed spans, our vented mesh reduces wind load.
Not sure which fabric is right? Order a free swatch pack and see the weight, texture and finish in your own hands before you commit to a full run.
What you can make with this fabric
Every application this fabric is suited to — tap through for sizes, templates and examples.
